Ghost Immobiliser Fitter
Ghost immobilisers can be an extremely effective method to protect your car from thieves. They stop vehicles from being started until the correct code is entered. They can be used to track vehicles remotely. They are becoming more popular and insurance companies are offering discounts to drivers with these systems fitted.
It is tamper proof.
The Ghost Immobiliser is an advanced security device that stops your vehicle from starting unless the unique PIN code is entered or a beacon is visible. The system is discreet and can be customised to fit your vehicle which makes it a highly efficient anti-theft device. After installation, it's important to test the system to ensure it is working correctly. Entering the PIN while starting the engine is an easy method to ensure that the system is installed correctly. Regular testing can identify any issues or issues with the system as early as is possible.
The system communicates with the ECU to stop your car from running unless the proper sequence is entered. This can be done using the electronic buttons that are located on your steering or through an app that you can download on your smartphone. Its low profile and tamperproof design make it difficult for thieves to steal. It can also be used as a beacon to track the location of your vehicle. It is an excellent option for protecting valuable vehicles that have been modified, or for those looking to secure their expensive or valuable automobiles.
This tamper proof device uses the buttons on your steering wheel to generate an exclusive sequence only known by you. The sequence is mathematically impossible for thieves to guess and can be changed easily by using a reset code. It can be installed by a technician on most vehicles.
After installing the device, you must connect it to an electrical source and a grounding point. Find the wiring diagram of your vehicle to identify the wires required. Be sure to insulate the connections with heat shrink tubing, or insulation tape to prevent short circuits and electrical damage. You should also check the connections and mounting for any indications of tampering by thieves.
The Ghost 2 immobiliser cost can be set to Service/Valet for older vehicles that require the battery isolation for maintenance or service. This will disable the device with an individual pin code, stopping it from being turned back on by thieves.
Wireless
In contrast to other anti-theft devices ghost immobilisers operate in a quiet manner and aren't detected by thieves. They can be fitted to a wide range of vehicles to guard against key cloning and hacking attacks and signal relay attacks. They also connect to the CAN network and are used to monitor a vehicle remotely. They can provide owners with instant notifications when their vehicle is stolen. Some insurance companies offer discounts to customers who install them. It is the most effective way to stop car theft.
The Ghost II immobiliser is an affordable and simple solution to ensure your vehicle is safe from theft. It is wireless and compatible with most cars. It is weatherproof and tamper proof which makes it a great choice for any type of vehicle. It also comes with a 3-year warranty. The Ghost II is unlike other security products in that it does not require any additional wiring or other external components. Its unique pin code sequence protects your car from key cloning and theft by stopping the engine from running unless a special disarm sequence is entered. The sequence could range from one to twenty buttons, so thieves will need to spend more time trying to hacking.
Another advantage of the Ghost II is its ability to block signals from a burglar's key fob. It can tell if a key fob is duplicated or stolen and shut down the engine by activating an alarm. It also stops the use of signal relay devices, which are commonly used by organised car thieves to gain access to vehicles.
It is crucial to test the Ghost Immobiliser system regularly to ensure that it is functioning properly. This will help you identify any issues early, and correct them before they become a significant issue. As part of your routine check-up of your vehicle, it's an ideal idea to test the system. Enter the PIN code into the system, and then turn on the engine.
It is crucial that the immobiliser be placed in a location that is hard to get at by thieves. If you can, hide the unit behind the dash using cable ties. Ensure that all connections are securely insulated and not exposed to theft by thieves. Make sure that the location of the mounting is secure.
It can be used with a variety of vehicles
The ghost immobiliser can be an extremely effective security device to prevent car theft. It works by blocking your vehicle's engine from starting until the proper pin code is entered. This code can be created by pressing a series of buttons on the steering wheel, door panel, or the centre console. The immobiliser is secure and can be programmed by the owner at anytime. It also shields against key-cloning and hacking.
While some drivers might try to install the Ghost Immobiliser themselves but it is recommended you hire an expert. The installation process is complicated and a mistake could render the device ineffective or even damage your vehicle. Additionally, DIY installation could invalidate warranties for both the Ghost Immobiliser and your vehicle.
The best place to begin is to find the wiring diagram of your vehicle model. This will provide a direction to locate the CAN H and L wires, which are connections to the immobiliser. Mark these wires once you have identified them so that they do not be accidentally disconnected during installation. Also, make sure you choose a reliable and safe grounding point for your system.
It is a good practice to test the immobiliser once the wires have been connected to ensure that everything is working properly. Enter the PIN code, then start your engine to determine whether everything works. It is also a good idea to test the immobiliser frequently to ensure it is working in the way it was intended to.
The ghost immobiliser is unique in that it doesn't require keys or LED indicators. It can be deactivated by a unique sequence that is displayed on your steering, door panel or the centre console. The immobiliser is also tamper-proof and does not leave any evidence of installation making it difficult for thieves to identify or disable. In addition, it can be used to increase the security of your vehicle in the event of a break-in, and is recommended by a variety of insurance companies.
Easy to install
The Ghost immobiliser is an advanced device that keeps your vehicle secure from the most skilled thieves. It prevents your car from starting until a distinct PIN or sequence is entered along with the key fob. This blocks hacking, cloning, and even key theft. Thieves aren't able to take your car away. It also makes use of a variety of other sensors that detect attempts at driving away and can notify the owner or the police in the case of any tampering.
Installing a Ghost immobiliser can be difficult, especially for those who haven't installed alarms or security systems before. It is essential to have the proper tools and materials to ensure a successful installation. A multimeter is helpful for verifying electrical values. Insulation tape and cable ties are also useful for protecting connections. The Ghost immobiliser user's manual contains specific guidelines that are specific to the specific model and wiring of your car.
During the installation process it is crucial to double-check the locations of the CAN H and L wires to ensure that they are in the correct locations. They are vital to powering the immobiliser, so mistakes could result in improper functioning or system failures. Label the wires with labels or tape so that you can track them. You should also determine the source of constant 12V and a grounding.
Once you've found the right location, you're now ready to begin to assemble the ghost immobiliser. To avoid short circuits or accidental airbag deployment, you will have to disconnect the battery first. The next step is to connect the wires. Make sure to follow the instructions in the user manual to ensure a clean and secure installation.
Once you've completed the wiring After you have completed the wiring, connect the Ghost immobiliser via CAN to the engine control unit. It will be a challenge for thieves, as the device is directly connected to the engine control unit, and it is not possible to remove or disable it. It's also secure against tampering, and the only method to disable it is entering a personal pin code. The pin code will only be known by the owner of the vehicle as well as the installer.
You can also use the Ghost immobiliser as a temporary solution to allow someone else to drive your car temporarily in the event that you're out of town for work or need an emergency service. This feature is referred to as the Service/Valet Mode, and it can be turned on using a key fob or mobile app.